Epoxy cure time and temperature
Cure time on the label is measured at one temperature and one thickness. Change either and the time changes. Here's what moves it and what the makers publish.
Three stages, three different times
- Working time: how long you have to pour and spread before it thickens.
- Tack-free, demold or sandable: hard enough to handle, sand or pull from the mold.
- Full cure: full hardness and strength. Usually days, not hours.
Recoat windows sit between the first two. See the guide to layer bonding.
What changes cure time
Temperature. The resin-hardener reaction runs faster when warm and slower when cold. Below the product's minimum it may not cure properly at all. Keep the shop, the wood and the epoxy in range through the cure, not just while you pour.
Thickness and mass. The reaction gives off heat, and a thick mass holds it, which speeds the cure further. A thin coat or a small casting loses heat and cures slower. EcoPoxy's FlowCast times are for a 38 mm deep, 14 L casting, and smaller pours cure more slowly. MAS says Deep Pour X poured under 2 in takes 48–72 h to cure.
Warm conditions shrink the safe pour depth. GlassCast 50 into wood: 25 mm per layer at 15–20 °C, 18 mm at 25 °C. TotalBoat says not to use Fathom above 80 °F.
Batch size in the cup. A big mixed batch left in a bucket heats up and kicks faster than the same epoxy spread out. GlassCast 50's pot life drops from 60 min for 500 g to 5 min for 5 kg.
Published cure times and temperature ranges
| Product | Handling | Full cure | Temperature |
|---|---|---|---|
| TotalBoat TableTop | Tack-free 6 h; sandable 24 h; light use 48 h (1/4 in at 70 °F) | 5–7 days | 65–80 °F, 0–60% humidity; 70 °F best |
| TotalBoat Fathom | Demold 48 h large castings, 72 h smaller | 5–7 days after the last layer | 60–80 °F; 70 °F best for thick pours |
| EcoPoxy FlowCast | Demold 3 days | 7–14 days | 68–77 °F; ideal 72 °F |
| MAS Deep Pour X | Tack-free about 12 h; sandable 24 h (2–3 in at 77 °F) | 5–7 days | 60–80 °F, held steady |
| System Three MirrorCast | Repour after 10–14 h | 7 days before sanding or finishing | 70–85 °F; best 70–80 °F |
| GlassCast 50 | Initial cure 96 h at 15 °C, 72 h at 20 °C, 48 h at 25 °C | About 7 days | 15–25 °C; 18–20 °C recommended |
| Stone Coat Countertop | Light use after 24 h | 30 days | 68–75 °F, 55–65% humidity |
GlassCast's numbers show the temperature effect directly: 10 °C warmer halves the time to initial cure. The epoxy comparison has every product's times.
Plan the schedule
The deep pour planner splits a pour into layers under the product's depth limit and gives the earliest and latest time for each next layer.
Cure time questions
How long does epoxy take to fully cure?
Usually days. TotalBoat TableTop lists 5–7 days, EcoPoxy FlowCast 7–14 days and Stone Coat Countertop 30 days. Check your product's data sheet before heavy use or sanding.
Does heat make epoxy cure faster?
Yes. Warmer epoxy reacts faster and gives off more heat, which also shortens working time and lowers the safe pour depth. Stay inside the temperature range on the data sheet.
Can epoxy cure in a cold garage?
Below the product's minimum it cures slowly or not completely. WEST SYSTEM 105/207 lists a 60 °F minimum cure temperature; most tabletop and deep-pour products want 65–80 °F. Heat the space and let the epoxy and wood come up to temperature before pouring.
Why is my thin pour of deep-pour epoxy taking so long?
Deep-pour epoxy is formulated to cure slowly so a thick layer doesn't overheat. A thin layer doesn't build up heat and cures slower still. MAS says Deep Pour X under 2 in takes 48–72 h to cure.